I spent last weekend maintaining my kitchen cabinets by attaching new sleek laminates with Masters Contact Cement. Within minutes, the wood surfaces bubbled up, the edges started peeling, and my whole effort was wasted.
If you have ever faced a similar situation, I have listed common mistakes and their solution while applying for Masters Contact Cement. Read the blog to explore the details.
Why is it Important to Apply Masters Contact Cement Right?
Avoiding common mistakes while applying Masters Contact Cement is crucial because it gives only a single chance to stick. It does not give a second chance for repositioning.
A smaller mistake can waste your time, energy, product, and money. Therefore, doing it right is very important.
6 Common Mistakes to Avoid While Applying Masters Contact Cement
Using Masters Contact Cement in right way is crucial to get desired results. You should avoid these common mistakes while applying adhesive:
1: Applying Excessive Amount of Masters Contact Cement
Application of too much amount of Masters Contact Cement can create the following problems:
◈ Creation of Mess: An excessive amount of Masters Contact Cement can create a mess. Cleaning the erupting adhesive from the edges, especially in woodworking projects, is difficult.
◈ Longer Drying Time: Heavy adhesive application takes a longer time to dry. It ultimately gives a bad bonding experience.
◈ Week Bonding: A high amount of cement gives inconstant curing that ultimately reduces the strength of the bond.
2: Spreading Too Little Adhesive
A too-small amount of adhesive can also create challenges in binding, such as:
◈ Bond-less Edges and Corners: Applying too little adhesive will leave the edges and patches on the surface cementless. It will result in a weak and compromised bond that will break over time.
◈ Unsatisfactory Finishing of Bonding: A small amount of adhesive will create an uneven finish, especially in shoe repair. It will be easily noticeable and destroy the look of the product.
How Can you Apply Adhesive in the Correct Amount?
Always apply Masters Contact Cement with a brush, roller, or spreader for a thin and even layer.
Tip: Focus on area coverage while applying adhesive, not on the volume.
3: Not Preparing Surface Properly
Most people apply adhesive without preparing the surface, especially for plastic, wood, rubber, and metal. They get a surprise that bonding is peeling off after a few hours.
How to Avoid it?
You can avoid it by properly cleaning and preparing the surface using sandpaper.
4: Not Choosing Adhesive Fit Your Environment
Every bonding product needs a specific environment to work best. People choose adhesives that do not match their environment. For example, some adhesives work best in cold environments but not in hot. Similarly, rain can also impact bonding ability.
What is the Solution?
Do some research about the working environment before buying an adhesive.
5: Using single adhesive for all the Jobs
Using the same kind of glue for all jobs is a common practice. For example, people are using household glue to fix leather shoes. It results in weak bonding and loss of money and product.
What Should You Do?
Always use Masters Contact Cement or other adhesives according to their jobs.
6: Ignoring Instructions on the Label
Another common mistake is that people do not read the instructions on the label before using the Masters Contact Cement. Either they think knowing everything or want to learn from the hit and trial method.
But this approach can be damaging. For Example, applying a Masters Contact Cement on the wrong surface can create problems while removing it.
How to Avoid It?
Always read instructions before using Masters Contact Cement. It will save you time and money.
Also Read this Blog: How to Apply and Get the Best Results with Masters Contact Cement Glue
Practical Tips For Professional Use of Masters Contact Cement
After fixing common mistakes, these practical tips will help to use Masters Contact Cement efficiently and have a professional finish:
➜ Test Before Use
Always test the Masters Contact Cement on the scrap before using it on your final project. It will save you time and energy.
➜ Clean to Tools
Clean to tools immediately after using Masters Contact Cement before it get dried.
➜ Avoid Harmful Fumes
Work in a well-aired area while using Masters Contact Cement to avoid its harmful fumes. You can also use a mask or respirator for your safety.
➜ Using the Right Tools
Use the correct tools for the Masters Contact Cement application. For instance, use a foam roller for large flat areas like plywood.
You can use small ship brushes for corners and edges. Similarly, have glue spreaders for consistent layer maintenance.
These are the small caring measures that give your finishing a professional look. Therefore, always give proper time and attention to these details.
Conclusion
Getting professional results from Masters Contact Cement is possible only when you do all the tasks without error. Preparing the surface for the final application of adhesive requires proper care and attention.
Avoiding common mistakes while using Masters Contact Cement gives you the best finish. Additionally, it saves your time, energy, and precious money. Follow these guidelines and share your experience in the comment section.
Frequently Asked Questions
Q1: What is the best rubber cement for shoes?
The Masters Contact Cement is the best for shoes. You can buy from the My Shoe Supplies website.
Q2: What is the drawback of Masters Contact Cement?
It bonds instantly, allowing you almost no time for repositioning. Therefore, it needs a wise use.
Q3: How to speed up Masters Contact Cement?
Applying the adhesive through the hot spray method can increase its bonding speed.
Q4: How to remove Master Contact Cement?
Remove the Masters Contact Cement before it is set. You can use a cleaning cloth dipped in hot water.
Q5: What is the solvent for Masters Contact Cement?
You can use different solvents for Masters Contact Cement, such as acetone, hexane, toluene, or hot water.
